Is down or not? does not work for you? We will check the status of with our worldwide server locations and detect if is offline just for you or there is a global outage.

Cheking Status for is Online or not?

Service Status Check below sources

Is it down only for you? Please check the instructions below.

Reports for last 24 hours
Live or not? Check below ALL tester #sources (different locations and servers)

Raspberry Pi behuizing - Model B / Pi 2 / Pi 3 ... - Opencircuit

Check out our other colors from the drop down on the right! ... It does not work for the Raspberry Pi Model A or B. It does work with the model A but there will be ...

Adafruit I2S 3W Class D Amplifier Breakout ... - Opencircuit

Verzonden vanaf € 2, - Nederland ... It takes standard I2S digital audio input and, not only decodes it into analog, but also amplifies it directly into a speaker. ... By connecting a pullup or pull down resistor, or wiring directly, the Gain pin can be ... weekly 0.8 2020-01-13T13:46:17 ...

This diagram only applies to the listed gear ratios. ... in (cable not included). weekly ... -dc-adjustable-voltage-step-down-module-lm2596s.jpg Dc-dc adjustable voltage ...

Large Surface Transducer with Wires - 4 Ohm 5 Watt - Opencircuit

This type of speaker does not have a moving cone like most speakers you've seen. Instead ... Verzonden vanaf € 4, - Nederland ... The body of the transducer is heavy so that it can be placed with the rubber top down on a table. And for ...

Adafruit DotStar Digitale RGB LED Strip - Zwart 60 ... - Opencircuit

Verzonden vanaf € 4, - Nederland ... control an infinite number of LEDs, just tack on more or cut off unwanted LEDs at the end. ... That means you need two pins, not one, to control DotStars. ... Hardware SPI support is handy but not required.

AlphaBot, Bluetooth robot building kit for Arduino - Opencircuit

Nederland. Verkocht ... Connecting with prototype breadboard, Supported, Not supported, Solder pads is provided for DIY interfaces to connecting with prototype ...

Adafruit RGB Matrix Bonnet voor de Raspberry Pi - Opencircuit

Verzonden vanaf € 2, - Nederland ... They do not work with older 26-pin boards like the original Model A or B. Note with the Pi ... Let me break it down for you:.

Witte LED Backlight Module - Groot 45mm x 86mm - Opencircuit

The trade-off is these are not flexible at all. Vraag en antwoord. Q Nederland Menno van hogezandKunnen deze panelen ...

Adafruit RFM96W LoRa Radio Transceiver Breakout ... - Opencircuit

The only difference is that there is no cat. ... Verzonden vanaf € 2, - Nederland ... The trade off is you need two or more radios, with matching frequencies.

Small Liquid Crystal Light Valve - Controllable Shutter ... - Opencircuit

Verzonden vanaf € 4, - Nederland ... Normally, it's a tinted gray color (because the light around us is not polarized, it is not completely clear). ... it up, or connect a draining resistor between the two pins to leak the voltage off when not powered.

Is it down only for you? Check these instructions
  • Use another browser. Check if the pages present the same problem with Internet Explorer, or another browser (Chrome, Firefox, Safari). If the problem also occurs, perform the following actions.
  • Use the IP address of website. Every Web site has a unique IP address. If the website you are attempting to visit contains the colon sign followed by a number in your address (for example, ), try removing that part ( ) or replace it with 80 ( ). If this does not work, you may not have given a correct address.
  • Check DNS cache validity. DNS is the service that converts the website's domain name into an IP address that web browser can use to connect to that site. That information is stored in your device's DNS cache to improve speed. However, if the information stored is corrupt or the website has changed its IP address, the browser may redirect you to another server.
  • Maybe website blocked you. Validate that the team administrator does not block these types of pages. In case if not, confirm what type of proxy settings you have to access the pages. To access it in Vista or Windows 7, click Start, type internet options, and press ENTER. In XP, select Start, then Run, type inetcpl.cpl, and press ENTER. Once you're there, click the Security tab, then the Restricted sites icon, followed by the Sites button. If the site's on this list, remove it. Then click the Privacy tab, and, again, the Sites button. Remove the URL if it's there.
Please rate functionality and service quality of from 1 to 5 stars.
Find their social accounts to contact them:




This website uses cookies to ensure you get the best experience on our website. If you continue browsing, we consider that you accept their use. Cookies Info